• idiomaddict@lemmy.world
          link
          fedilink
          arrow-up
          12
          ·
          11 days ago

          Holy fuck that seems like a tedious, difficult, messy job. I’ve also never heard of it, and I feel like the homeowners I know would have bitched about it to me before if they had to do it. I looked it up, and there’s all sorts of scenarios in which they might not have to do that (anode rods and tankless water heaters both seem pretty cool and there are services for it), but I might just send out a couple of texts. Water heaters are nothing to fuck with.

            • FireRetardant@lemmy.world
              link
              fedilink
              arrow-up
              6
              ·
              11 days ago

              If it has a valve on the outlet of the water heater, you can close that and flush cold water through the heater and out the bottom drain by opening the drain. This will also have more pressure and volume of water to flush with.

          • PM_Your_Nudes_Please@lemmy.world
            link
            fedilink
            arrow-up
            5
            ·
            11 days ago

            It’s tedious, but it’s mostly just a matter of waiting for the water to heat back up afterwards.

            Unplug the heater, then run the bathtub until you’re out of hot water. Turn off the bathtub, and turn off the water supply going into the heater. Attach a garden hose to the bottom of the heater, and run it to a drain somewhere. Turn the hot water on somewhere like a sink, to provide a vent to the system; It won’t run because the supply is turned off, but it’ll at least allow air into the system for when you drain the heater. Use the spigot at the bottom of the heater to drain it.

            Be prepared for a gross rush of water at first, because all of the sediment and rust will have settled to the bottom of the heater where the spigot is. Once it’s drained, you can do whatever maintenance you need. For instance, you probably need to replace the cathode rod, which is designed to wear away over time to protect the rest of the heater from corrosion.

            To do a final flush, you can open the water inlet at the top of the tank. It’ll help drain any last remaining sediment out of the tank. Then turn off the water inlet, turn off the spigot, disconnect the hose, and leave the sink tap open while you refill the tank with fresh water.

            The whole process only takes like 30 minutes, and then you’re just waiting for the heater to come back up to temperature afterwards.

            • MutilationWave@lemmy.world
              link
              fedilink
              arrow-up
              4
              ·
              edit-2
              11 days ago

              Wow thanks for the info. My heater tank just shit the bed a month ago, flooding water all over my unfinished cave of a basement. I rent this place, so all in all for me it was great. My landlord replaced it with a pretty decent and bigger tank, the plumber replaced a lot of our 100 year old pipes with new brass, so now my wife and I can do showers back to back in the winter with hot water.

              Hopefully we’ll become homeowners in 2025 so I’m saving this for the future.

              Edit: I forgot! We had nuts water pressure before,125 psi, but the plumber said he had to put a limiter on by law. Probably will save us a bit of money.

        • fmstrat@lemmy.nowsci.com
          link
          fedilink
          English
          arrow-up
          6
          ·
          11 days ago

          Incandescent light bulbs. LEDs in standard bulbs typically don’t get hot enough, especially since the casings are plastic instead of glass.

        • RememberTheApollo_@lemmy.world
          link
          fedilink
          arrow-up
          9
          ·
          edit-2
          11 days ago

          Nope. That’s inside the engine core. This is just an aerodynamic tail cone for the engine that serves to streamline exhaust airflow and maintain cross sectional area for the exhaust where it exits the engine. Makes for less turbulence and noise.

    • Jarix@lemmy.world
      link
      fedilink
      arrow-up
      4
      ·
      11 days ago

      Clean any shiny metal decorative things that get very hot before. Such as stoves and and fireplaces if you want to avoid burning in such things

  • Agent641@lemmy.world
    link
    fedilink
    arrow-up
    31
    ·
    11 days ago

    Slaps side of jet nozzle

    “This bad boy can fit so many degrees of skin burn, like at least 3”

  • Steamymoomilk@sh.itjust.works
    link
    fedilink
    English
    arrow-up
    6
    ·
    edit-2
    11 days ago

    Chapter 4 Of the Boeing pre flight check list.

    Percussive Maintenance is mandatory So what if the jet engine is really hot? You give the plane a high five for landing!!

  • leds@feddit.dk
    link
    fedilink
    arrow-up
    5
    ·
    11 days ago

    For a moment I thought it was showing the reflection of a huge fireball explosion

      • toynbee@lemmy.world
        link
        fedilink
        arrow-up
        8
        ·
        10 days ago

        Looks to be something that gets very hot, possibly an engine, possibly attached to an aircraft; and it seems that someone touched it before waiting for it to cool after use, leaving a probably very painful handprint.

        That’s my interpretation, at least.

        • MonkderVierte@lemmy.ml
          link
          fedilink
          arrow-up
          5
          arrow-down
          1
          ·
          edit-2
          10 days ago

          Oh, didn’t see the handprint. But looks like a normal (cold) handprint on stainless steel to me.

          • toynbee@lemmy.world
            link
            fedilink
            arrow-up
            4
            ·
            10 days ago

            Unfortunately, I am too ignorant on the subject to say, but I think what I described above is what the OP intended to represent.